Research output per year
Research output per year
- 1 - 50 out of 174 results
Search results
-
2023
Computational study of the geometrical influence of grain topography on short crack propagation in AA7XXX series alloys
Grant, C., Al Aboura, Y., Burnett, T., Prangnell, P. & Shanthraj, P., 15 May 2023, (Accepted/In press) In: Materialia.Research output: Contribution to journal › Article › peer-review
Open AccessFile30 Downloads (Pure) -
In situ observation of environmentally assisted crack initiation and short crack growth behaviour of new-generation 7xxx series alloys in humid air
Euesden, R., Al Aboura, Y., Garner, A., Jailin, T., Grant, C., Barrett, Z., Engel, C., Shanthraj, P., Holroyd, N., Prangnell, P. & Burnett, T., 15 May 2023, In: Corrosion Science.Research output: Contribution to journal › Article › peer-review
Open Access -
Mechanisms of Environmentally Induced Crack Initiation in Humid Air for New-Generation Al-Zn-Mg-Cu Alloys
Burnett, T., Prangnell, P., Al Aboura, Y., Euesden, R., Grant, C., Yao, Y., Curd, M., Garner, A., Holroyd, N. J. H., Barrett, Z. & Engel, C., 10 Jul 2023, In: Corrosion.Research output: Contribution to journal › Article › peer-review
Open AccessFile96 Downloads (Pure) -
Wire-arc directed energy deposition of Inconel 718: Effects of heat input and build interruptions on mechanical performance
Kindermann, R. M., Roy, M., Morana, R., Francis, J. & Prangnell, P., Aug 2023, In: Additive Manufacturing. 76, 103765Research output: Contribution to journal › Article › peer-review
Open Access -
β grain refinement during solidification of Ti-6Al-4V in Wire-Arc Additive Manufacturing (WAAM)
Kennedy, J. R., Davis, A., Caballero, A. E., Pickering, E. & Prangnell, P., 8 Mar 2023, IOP Conference Series: Materials Science and Engineering. 1 ed. Vol. 1274. 012005. (IOP Conference Series: Materials Science and Engineering).Research output: Chapter in Book/Report/Conference proceeding › Conference contribution › peer-review
Open Access -
2022
CALPHAD-informed phase-field model for two-sublattice phases based on chemical potentials: η-phase precipitation in Al-Zn-Mg-Cu alloys
Liu, C., Davis, A., Fellowes, J., Prangnell, P., Raabe, D. & Shanthraj, P., 1 Mar 2022, In: Acta Materialia. 226, 117602.Research output: Contribution to journal › Article › peer-review
Open AccessFile111 Downloads (Pure) -
Comparison of Microstructure Refinement in Wire-Arc Additively Manufactured Ti-6Al-2Sn-4Zr-2Mo-0.1Si and Ti-6Al-4V Built with Inter-Pass Deformation
Davis, A., Caballero, A. E., Biswal, R., Williams, S. & Prangnell, P., 5 Aug 2022, (Accepted/In press) In: Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science.Research output: Contribution to journal › Article › peer-review
-
Large-scale serial sectioning of environmentally assisted cracks in 7xxx Al alloys using femtosecond Laser-PFIB
Burnett, T., Garner, A., Donoghue, J., Al Aboura, Y., Prangnell, P. & Winiarski, B., 12 Apr 2022, In: Materials Characterization.Research output: Contribution to journal › Article › peer-review
Open Access -
Microstructural characterisation and mechanical properties of Ti-5Al-5V-5Mo-3Cr built by Wire and Arc Additive Manufacture
Caballero, A., Davis, A., Kennedy, J., Fellowes, J., Garner, A., Williams, S. & Prangnell, P., 8 Aug 2022, (Accepted/In press) In: Philosophical Magazine.Research output: Contribution to journal › Article › peer-review
-
Modelling of Friction Stir Welded AA2139 Aluminium Alloy Panels in Tension and Blast
Awang Draup, A. J., Rodgers, B., Prangnell, P., Li, Q., Lunt, M. J. & Robson, J., 1 May 2022, In: International Journal of Impact Engineering. 163, 104163.Research output: Contribution to journal › Article › peer-review
Open Access -
Optimising large-area crystal orientation mapping of nanoscale β phase in α + β titanium alloys using EBSD
Davis, A., Zeng, X., Thomas, R., Kennedy, J., Donoghue, J., Gholinia, A., Prangnell, P. & Da Fonseca, J. Q., 7 Oct 2022, In: Materials Characterization. 112371.Research output: Contribution to journal › Article › peer-review
-
Understanding the environmentally assisted cracking (EAC) initiation and propagation of new generation 7xxx alloys using slow strain rate testing
Burnett, T., Al Aboura, Y., Euesden, R., Garner, A. & Prangnell, P., 16 Feb 2022, In: Corrosion Science.Research output: Contribution to journal › Article › peer-review
-
β Grain refinement by yttrium addition in Ti-6Al-4V Wire-Arc Additive Manufacturing
Kennedy, J., Davis, A., Caballero, A. F., Byres, N., Williams, S., Pickering, E. & Prangnell, P., 25 Feb 2022, In: Journal of Alloys and Compounds. 895, p. 162735Research output: Contribution to journal › Article › peer-review
-
2021
CALPHAD-informed phase-field modeling of grain boundary microchemistry and precipitation in Al-Zn-Mg-Cu alloys
Liu, C., Garner, A., Zhao, H., Prangnell, P., Gault, B., Raabe, D. & Shanthraj, P., 5 May 2021, (Accepted/In press) In: Acta Materialia.Research output: Contribution to journal › Article › peer-review
-
Co-deformation and dynamic annealing effects on the texture development during alpha–beta processing of a model Zr-Nb alloy
Daniel, C. S., Garner, A., Honniball, P. D., Bradley, L., Preuss, M., Prangnell, P. B. & Quinta Da Fonseca, J., 1 Feb 2021, In: Acta Materialia. 205, p. 116538Research output: Contribution to journal › Article › peer-review
-
In-Situ Observation of Single Variant α Colony Formation in Ti-6Al-4V
Davis, A., Donoghue, J., Kennedy, J., Byres, N. & Prangnell, P., 20 Sept 2021, In: Acta Materialia. 117315.Research output: Contribution to journal › Article › peer-review
Open AccessFile14 Downloads (Pure) -
Multiscale analysis of grain boundary microstructure in high strength 7xxx Al alloys
Garner, A., Euesden, R., Yao, Y., Aboura, Y., Zhao, H., Donoghue, J., Curioni, M., Gault, B., Shanthraj, P., Barrett, Z., Engel, C., Burnett, T. L. & Prangnell, P. B., 1 Jan 2021, In: Acta Materialia. 202, p. 190-210 21 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile75 Downloads (Pure) -
Tailoring Equiaxed β-grain Structures in Ti-6Al-4V Coaxial Electron Beam Wire Additive Manufacturing
Davis, A., Kennedy, J. R., Strong, D., Kovalchuk, D., Porter, S. & Prangnell, P., 2021, In: Materialia.Research output: Contribution to journal › Article › peer-review
-
The evolution of abnormally coarse grain structures in beta-annealed Ti-6Al%-4V% rolled plates, observed by in-situ investigation
Byres, N., Quinta da Fonseca, J., Daniel, C., Donoghue, J., Davis, A., Shanthraj, P., Dod, B. & Prangnell, P., 1 Dec 2021, In: Acta Materialia. 221, 117362.Research output: Contribution to journal › Article › peer-review
-
The Potential for Grain Refinement of Wire-Arc Additive Manufactured (WAAM) Ti-6Al-4V by ZrN and TiN Inoculation
Kennedy, J., Davis, A., Caballero, A., Williams, S., Pickering, E. & Prangnell, P., 23 Feb 2021, In: Additive Manufacturing.Research output: Contribution to journal › Article › peer-review
Open AccessFile171 Downloads (Pure) -
2020
Confirmation of Rapid-Heating β Recrystallization in Wire-Arc Additively Manufactured Ti-6Al-4V
Davis, A., Caballero, A. & Prangnell, P., 31 Jul 2020, (Accepted/In press) In: Materialia.Research output: Contribution to journal › Article › peer-review
-
Direct observation of the dynamic evolution of precipitates in aluminium alloy 7021 at high strain rates via high energy synchrotron X-rays
Mirihanage, W. U., Robson, J. D., Mishra, S., Hidalgo-manrique, P., Da Fonseca, J. Q., Daniel, C. S., Prangnell, P. B., Michalik, S., Magdysyuk, O. V., Connolley, T. & Drakopoulos, M., 2 Dec 2020, (E-pub ahead of print) In: Acta Materialia. p. 116532Research output: Contribution to journal › Article › peer-review
-
Environmental Cracking Performance of New Generation Thick Plate 7000-T7x series Alloys in Humid Air
Schwarzenböck, E., Ollivier, E., Garner, A., Cassell, A., Hack, T., Barrett, Z., Engel, C., Burnett, T., Holroyd, N., Robson, J. & Prangnell, P., 22 Apr 2020, (Accepted/In press) In: Corrosion Science.Research output: Contribution to journal › Article › peer-review
-
Isomorphic Grain Inoculation in Ti-6Al-4V during Additive Manufacturing
Kennedy, J., Davis, A., Caballero, A., Garner, A., Donoghue, J., Zollinger, J., Bouzy, E., Pickering, E. & Prangnell, P., 10 Dec 2020, In: Materials Letters: X.Research output: Contribution to journal › Article › peer-review
Open Access -
Process response of Inconel 718 to wire + arc additive manufacturing with cold metal transfer
Kindermann, R., Roy, M., Morana, R. & Prangnell, P., 16 Aug 2020, In: Materials & Design. 109031.Research output: Contribution to journal › Article › peer-review
Open Access -
Quantification of strain fields and grain refinement in Ti-6Al-4 V inter-pass rolled wire-arc AM by EBSD misorientation analysis
Davis, A., Hönnige, J. R., Martina, F. & Prangnell, P., 25 Sept 2020, (E-pub ahead of print) In: Materials Characterization. p. 110673Research output: Contribution to journal › Article › peer-review
-
The Effectiveness of Grain Refinement by Machine Hammer Peening in High Deposition Rate Wire-Arc AM Ti-6Al-4V
Hönnige, J. R., Davis, A. E., Ho, A., Kennedy, J. R., Neto, L., Prangnell, P. & Williams, S., 6 May 2020, (E-pub ahead of print) In: Metallurgical and Materials Transactions A.Research output: Contribution to journal › Article › peer-review
Open Access -
The effect of loading direction on strain localisation in wire arc additively manufactured Ti–6Al–4V
Lunt, D., Ho, A., Davis, A., Harte, A., Martina, F., Quinta da Fonseca, J. & Prangnell, P., 21 May 2020, (E-pub ahead of print) In: Materials Science and Engineering A: Structural Materials: Properties, Microstructures and Processing . 139608.Research output: Contribution to journal › Article › peer-review
Open Access -
The effect of processing parameters on rapid-heating β recrystallization in inter-pass deformed Ti-6Al-4V wire-arc additive manufacturing
Davis, A. E., Kennedy, J. R., Ding, J. & Prangnell, P. B., 1 May 2020, In: Materials Characterization. 163, p. 110298Research output: Contribution to journal › Article › peer-review
-
2019
Automated Image Mapping and Quantification of Microstructure Heterogeneity in Additive Manufactured Ti6Al4V
Zhao, H., Ho, A., Davis, A., Antonysamy, A. A. & Prangnell, P., Jan 2019, In: Materials Characterization. 147, p. 131-145 14 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile278 Downloads (Pure) -
Effect of processing parameters on the densification, microstructure and crystallographic texture during the laser powder bed fusion of pure tungsten
Sidambe, A. T., Tian, Y., Prangnell, P. B. & Fox, P., 1 Jan 2019, In: International Journal of Refractory Metals and Hard Materials. 78, p. 254-263 10 p.Research output: Contribution to journal › Article › peer-review
Open Access -
Mechanical performance and microstructural characterisation of titanium alloy-alloy composites built by wire-arc additive manufacture
Davis, A. E., Breheny, C. I., Fellowes, J., Nwankpa, U., Martina, F., Ding, J., Machry, T. & Prangnell, P. B., 23 Sept 2019, In: Materials Science and Engineering: A . 765, p. 138289Research output: Contribution to journal › Article › peer-review
Open Access -
On the Origin of Microstructural Banding in Ti-6Al4V Wire-Arc Based High Deposition Rate Additive Manufacturing
Ho, A., Zhao, H., Fellowes, J., Martina, F., Davis, A. & Prangnell, P., 1 Mar 2019, In: Acta Materialia. 166, p. 306-323 18 p.Research output: Contribution to journal › Article › peer-review
Open Access -
Weld zone and residual stress development in AA7050 stationary shoulder friction stir T-joint weld
Sun, T., Roy, M. J., Strong, D., Simpson, C., Withers, P. J. & Prangnell, P. B., 1 Jan 2019, In: Journal of Materials Processing Technology. 263, p. 256-265 10 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile22 Downloads (Pure) -
2018
Evaluation of Zn-Rich Coatings for IMC Reaction Control in Aluminum- Magnesium Dissimilar Welds
Wang, Y. & Prangnell, P., 2018, In: Materials Characterization.Research output: Contribution to journal › Article › peer-review
Open AccessFile177 Downloads (Pure) -
Material interactions in laser polishing powder bed additive manufactured Ti6Al4V components
Tian, Y., Gora, W. S., Cabo, A. P., Parimi, L. L., Hand, D. P., Tammas-Williams, S. & Prangnell, P., Mar 2018, In: Additive Manufacturing. 20, p. 11-12 2 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile251 Downloads (Pure) -
The Effect of Shoulder Coupling on the Residual Stress and Hardness Distribution in AA7050 Friction Stir Butt Welds
Sun, T., Reynolds, A. P., Roy, M. P., Withers, P. & Prangnell, P., 26 Sept 2018, In: Journal of Materials Science and Engineering. A . 735Research output: Contribution to journal › Article › peer-review
Open AccessFile231 Downloads (Pure) -
2017
Application of bulk deformation methods for microstructural and material property improvement and residual stress and distortion control in additively manufactured components
Colegrove, P. A., Donoghue, J., Martina, F., Gu, J., Prangnell, P. & Hönnige, J., Jul 2017, In: Scripta Materialia. 135, p. 111-118 8 p.Research output: Contribution to journal › Article › peer-review
Open Access -
Comparison of residual stress distributions in conventional and stationary shoulder high-strength aluminum alloy friction stir welds
Sun, T., Roy, M., Strong, D., Withers, P. & Prangnell, P., Apr 2017, In: Journal of Materials Processing Technology. 242, p. 92-100 8 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile473 Downloads (Pure) -
Investigation of residual stress distribution and texture evolution in AA7050 stationary shoulder friction stir welded joints
Sun, T., Tremsin, A. S., Roy, M., Hofmann, M., Prangnell, P. & Withers, P., 2017, In: Materials Science and Engineering A: Structural Materials: Properties, Microstructures and Processing .Research output: Contribution to journal › Article › peer-review
Open AccessFile192 Downloads (Pure) -
The Effectiveness of Al-Si Coatings for Preventing Interfacial Reaction in Al - Mg Dissimilar Metal Welding
Wang, Y., Al-Zubaidy, B. & Prangnell, P., 2017, In: Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science. 15 p.Research output: Contribution to journal › Article › peer-review
Open Access -
The Influence of Grain Structure on Intermetallic Compound Layer Growth Rates in Fe-Al Dissimilar Welds
Xu, L., Robson, J., Wang, L. & Prangnell, P., 2017, In: Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science. p. 1-12 12 p.Research output: Contribution to journal › Article › peer-review
Open Access -
The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P. J., Todd, I. & Prangnell, P. B., 2017, In: Scientific Reports. 7, 1, 7308.Research output: Contribution to journal › Article › peer-review
Open Access -
The significance of intermetallic compounds formed during interdiffusion in aluminum and magnesium dissimilar welds
Wang, Y. & Prangnell, P., Dec 2017, In: Materials Characterization. 134, p. 84-95 12 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile200 Downloads (Pure) -
2016
Characterisation of Weld Zone Reactions in Dissimilar Glass-to-Aluminium Pulsed Picosecond Laser Welds
Ciuca, O., Carter, R., Prangnell, P. & Hand, D. P., Oct 2016, In: Materials Characterization. 120, p. 53-62Research output: Contribution to journal › Article › peer-review
Open AccessFile324 Downloads (Pure) -
Dissimilar ultrasonic spot welding of aerospace aluminum alloy AA2139 to titanium alloy TiAl6V4
Prangnell, P., Zhang, C. Q. & Robson, J., 2016, In: Journal of Materials Processing Technology. 231, p. 382–388 7 p.Research output: Contribution to journal › Article › peer-review
Open Access -
Effect of Interfacial Reaction on the Mechanical Performance of Steel to Aluminum Dissimilar Ultrasonic Spot Welds
Xu, L., Wang, L., Chen, Y-C., Robson, J. & Prangnell, P., Jan 2016, In: Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science. 47, 1, p. 334-346 12 p.Research output: Contribution to journal › Article › peer-review
Open AccessFile1117 Downloads (Pure) -
Effect of microstructure on the tensile strength of Ti6Al4V specimens manufactured using Additive Manufacturing Electron Beam Process
Machry, T., Eatock, E., Meyer, J., Antonysamy, A. A., Ho, A. & Prangnell, P., 2016, In: Powder Metallurgy. 59, p. 41-50 10 p.Research output: Contribution to journal › Article › peer-review
-
Enhancing surface finish of additively manufactured titanium and cobalt chrome elements using laser based finishing
Gora, W. S., Tian, Y., Cabo, A. P., Ardron, M., Maier, R. J., Prangnell, P. B., Weston, N. & Hand, D. P., 16 Sept 2016, In: Physics Procedia. 83, p. 258–263Research output: Contribution to journal › Article › peer-review
Open Access -
Porosity Regrowth During Heat Treatment of Hot Isostatically Pressed Additively Manufactured Titanium Components
Tammas-Williams, S., Withers, P., Todd, I. & Prangnell, P., Sept 2016, In: Scripta Materialia. 122, p. 72-76 5 p.Research output: Contribution to journal › Article › peer-review
Open Access6 Downloads (Pure)