Abstract
Objectives
This study aims to evaluate the solubility, pH, Ca2 + release, setting time, and hydroxyapatite (HAp) formation of the tested materials.
Methods
Four study groups were tested: NEX-MTA (NMTA; GC, Japan), NMTA with phosphorylated pullulan (MTA-PPL), NMTA with poly-PS (MTA-polyPS), and Biodentine (BD; Septodont, France). Solubility was measured after 7 and 28 days at 37 °C in deionized water. Ca2+ release and pH evaluation were performed after immersion in deionized water at 3 h, 24 h, 7 days, and 28 days using pH and Ca2+ meters. Setting times were determined with a Vicat apparatus, and apatite precipitation was evaluated through scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/ EDS) and Fourier transform infrared spectroscopy (FTIR) analysis 28 days in phosphate-buffered saline.
Results
NMTA showed the lowest solubility; however, there was no statistically significant difference between NMTA and MTA-polyPS (P > 0.05). NMTA exhibited the most alkaline pH at all measured time points. Although MTA-polyPS consistently showed lower pH values than NMTA throughout the observation periods, no statistically significant differences were observed among MTA-polyPS, BD, and MTA-PPL at 28 days (P > 0.05). BD released the most Ca2+, with MTA-polyPS releasing the least. BD exhibited the shortest initial and final setting time (9.2 and 42 min, respectively), followed by MTA-polyPS, MTA-PPL, and NMTA. SEM/ EDS and FTIR indicated that MTA-polyPS had the highest apatite precipitation, with Ca/P ratios of 1.70 (NMTA) and 1.79 (MTA-polyPS). MTA-PPL and BD showed no significant apatite precipitation, with Ca/P ratios of 3.93 and 34.9, respectively.
Significance
The incorporation of polyPS into calcium silicate-based cement may enhance apatite precipitation and accelerate the setting without altering the pH and solubility property.
This study aims to evaluate the solubility, pH, Ca2 + release, setting time, and hydroxyapatite (HAp) formation of the tested materials.
Methods
Four study groups were tested: NEX-MTA (NMTA; GC, Japan), NMTA with phosphorylated pullulan (MTA-PPL), NMTA with poly-PS (MTA-polyPS), and Biodentine (BD; Septodont, France). Solubility was measured after 7 and 28 days at 37 °C in deionized water. Ca2+ release and pH evaluation were performed after immersion in deionized water at 3 h, 24 h, 7 days, and 28 days using pH and Ca2+ meters. Setting times were determined with a Vicat apparatus, and apatite precipitation was evaluated through scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/ EDS) and Fourier transform infrared spectroscopy (FTIR) analysis 28 days in phosphate-buffered saline.
Results
NMTA showed the lowest solubility; however, there was no statistically significant difference between NMTA and MTA-polyPS (P > 0.05). NMTA exhibited the most alkaline pH at all measured time points. Although MTA-polyPS consistently showed lower pH values than NMTA throughout the observation periods, no statistically significant differences were observed among MTA-polyPS, BD, and MTA-PPL at 28 days (P > 0.05). BD released the most Ca2+, with MTA-polyPS releasing the least. BD exhibited the shortest initial and final setting time (9.2 and 42 min, respectively), followed by MTA-polyPS, MTA-PPL, and NMTA. SEM/ EDS and FTIR indicated that MTA-polyPS had the highest apatite precipitation, with Ca/P ratios of 1.70 (NMTA) and 1.79 (MTA-polyPS). MTA-PPL and BD showed no significant apatite precipitation, with Ca/P ratios of 3.93 and 34.9, respectively.
Significance
The incorporation of polyPS into calcium silicate-based cement may enhance apatite precipitation and accelerate the setting without altering the pH and solubility property.
| Original language | English |
|---|---|
| Pages (from-to) | 1058-1066 |
| Journal | Dental Materials |
| Volume | 41 |
| Issue number | 9 |
| Early online date | 20 Jun 2025 |
| DOIs | |
| Publication status | Published - 30 Sept 2025 |